Everyone will have their own unique perception when it comes to How to Install a Bathtub.
Mounting a bathtub isn't specifically brain surgery, but it does require solid plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old bath tub with a new one is additionally a reasonably difficult project. If the old bathtub is readily accessible, the task can relocate speedily; if you have to open up a wall to eliminate the old tub and place the new bathtub, the job is a lot harder. In either case, the project is within a residence handyman's abilities, although you will certainly require a helper to vacate the old bathtub as well as set in the new one. Make sure you have certified on your own for the task and are comfortable trying it. Instead of working with a service provider to take over a halfway-completed job, it is better to take into consideration employing one before you start. Opportunities are you might need a professional plumber to make tube links.
This post will certainly help you install a new bathtub in your restroom if you have actually already acquired a new bathtub and do not require to transform the plan of your previous supply of water pipes.
Your devices and also material checklist need to comprise the following:
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you should do is detach the supply of water. After doing so, turn on the taps to drain any water staying in the system. The process of getting rid of the existing faucets can be fairly problematic due to the restricted gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth all set for the staying water that will certainly come from the pipes. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this process. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin guaranteeing that the washers are in place between the faucet as well as the sink. Safeguard the tap in place with the producer offered backnut. When the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical faucet ports. The previous kind ought to be connected to the tap finishes first, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Making use of the two wood boards under its feet, put the bath tub in the required setting. The wooden boards are valuable in equally spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 small points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level and changing the feet on the tub till the level reads level.
To mount taps, fit the bottom of the furthest adaptable tap connector to the proper supply pipe by making a compression sign up with; then do the exact same for the other tap.
Activate the water system as well as examine all joints as well as new pipework for leakages and tighten them if required. Load the tub and likewise inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Ultimately, repair the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and sealing around the tub must wait till the tub has actually been made use of a minimum of once as this will resolve it into its last position.
Getting ready for the Installment
Firstly, the supporting structure provided with the bath should be fitted (if called for) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps system to stop pressure on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the location where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to crack a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, causing complications with wetness and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, and also are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub remains in use. The sealer can break relatively early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that article on How to Install a Bathtub Yourself through a good friend on a different web blog. Enjoyed reading our article? Please share it. Let someone else find it. I value reading our article about A Step-by-Step Guide to Installing a Bathtub.
Reliable plumber? Dial!